Blogarchiv
Raumfahrt - China´s Change3-Mond-Rover - Update 4

.

Figure2 APXS on Yutu rover of Chang’e-3 mission (image by Xinhua)

.

Chang'e-3 satellite payload APXS obtained its first spectrum of lunar regolith

The Active Particle-induced X-ray Spectrometer (APXS), carried by the Yutu rover of the Chang’e-3 satellite got its first X-ray fluorescence spectrum of lunar regolith around the landing site on December 25, 2013.

An initial analysis indicates that eight major rock-forming elements (Mg, Al, Si, K, Ca, Ti, Cr and Fe) and at least 3 minor elements (Sr, Y and Zr) of the Moon can be identified in this spectrum. Besides, the energy resolution of AXS is estimated to be about 135 @5.9keV, which demonstrates that it is currently one of the best X-ray spectrometer for the planetary exploration in the world.

APXS was firstly powered on December 23 and an in-flight calibration of a standard basalt rock sample mounted on the rover was accomplished in five minutes, which proved its stable performance on the Moon. Two days later, APXS was successfully deployed to about two to three centimeters above the lunar regolith surface by the robotic arm of Yutu and started the detection mode. APXS was not only an X-ray spectrometer, but also served as a distance sensor during the deployment by making use of X-ray count rate varied with distance.

The Institute of High Energy Physics (IHEP) developed APXS in collaboration with the Purple Mountain Observatory (PMO), CAS. Prior to the APXS on Chang’e-3, two X-ray Spectrometers onboard Chang’e-1 and Chang’e-2 developed by IHEP scientists were launched respectively on October, 2007 and October, 2010.

.

Figure 1 APXS (Sensor head, Radioactive Heat Unit and Inflight calibration target),image by IHEP

.

Figure 3 First X-ray fluorescent spectrum of lunar regolith obtained by APXS (image by IHEP)

.

Quelle: Institute of High Energy Physics, CAS

.

Update: 4.01.2014

.

China moon rover stamps and medallions celebrate country's first lunar

landing

.

Quelle: SC

.

Update: 12.01.2014

.

Moon rover, lander wake after lunar night

.

BEIJING, China's moon rover "Yutu" (Jade Rabbit) and the Chang'e-3 lander have just "woken up" after a period of dormancy that lasted two weeks, or one lunar night, in a move designed to ride out harsh climactic conditions.

Yutu was awakened autonomously at 5:09 a.m. Beijing Time on Saturday and has finished necessary setting procedures and entered a normal working mode following orders from the Beijing Aerospace Control Center (BACC), according to a statement issued by the BACC on Sunday.

It has started its rove around the moon surface and scientific missions.

Chang'e-3 has also been awakened automatically at 8:21 a.m. on Sunday, and is currently in normal condition, the statement said.

One night on the moon lasts about 14 days on Earth, during which the temperature falls below minus 180 celsius and there is no sunlight to provide power to the instruments' solar panels.

"During the lunar night, the lander and the rover were in a power-off condition and the communication with Earth was also cut off," said Zhou Jianliang, chief engineer of the BACC.

"When the night ends, they will be started up with the power provided by sunlight and resume operation and communication according to preset programs," Zhou said.

The awakening of the rover and lander marks the success of Chinese technology in surviving the lunar night, and the center will instruct the two instruments to carry on scheduled exploration missions, the chief engineer added.

Chang'e-3 soft-landed on the moon's Sinus Iridium, or the Bay of Rainbows, on Dec. 14 last year, and Yutu later separated from the lander.

The rover fell asleep on Dec. 26 as the mission's first lunar night arrived. 

The Chang'e 3 lander captures a picture of Earth surrounded by the blackness of space on Dec. 25.

Quelle: Xinhua

.

Update: 15.01.2014

.

China's moon rover performs first lunar probe
BEIJING, China's moon rover "Yutu", or Jade Rabbit, completed its first scientific exploration of lunar soil on Tuesday, the Beijing Aerospace Control Center (BACC) said.
The rover used its mechanical arm to survey the lunar soil at 21:45 Beijing Time, following instructions from the control center, according to a BACC statement.
The exploration lasted about half an hour and every operation was precisely performed by the rover, it said.
"Accuracy control of the mechanical arm at a distance of 380,000 kilometers has been realized in the probe, making China's breakthrough in controlling a mechanical arm with high precision on the lunar surface," said Wu Fenglei of the BACC.
The rover completed an arm flexing assessment on Dec. 23, a key test before beginning the soil survey and other work on the surface, said the center.
Yutu will survey the moon's geological structure and surface substances and look for natural resources for three months, while the lander will conduct in-situ exploration at the landing site for one year.
Quelle: Xinhua

.

 

Update: 17.01.2014 

.

China's Jade Rabbit rover explores Moon soil

China's Jade Rabbit Moon rover has completed its first examination of the lunar soil, state media claim.
The Beijing Aerospace Control Center said the rover had explored the surface using its mechanical arm on Tuesday night (Beijing time).
The survey lasted half an hour and official news service Xinhua said the rover performed well in the tests.
In December, the Chinese landing module and rover made the first "soft" landing on the Moon since 1976.
The mission is designed to test new technologies, gather scientific data and build intellectual expertise.
The lander will operate there for a year, while the rover is expected to work for about three months.
.
Chang'e-3 mission instruments
On the lander:
Optical ultraviolet telescope for astronomy
Ultraviolet camera to monitor space weather
Descent camera to monitor the landing
On the rover:
Two panoramic cameras
Engineering and navigation cameras
Arm-mounted alpha particle X-ray spectrometer to analyse chemical elements in rocks and soil
Infrared spectrometer to study minerals
Ground-penetrating radar to map the structure of lunar soil and crust down to several hundred feet
.
The operation tested the ability by ground stations to precisely control the robot over a distance of some 380,000km - one of those key technologies Chinese space scientists are keen to master.
Wu Fenglei, from the Beijing control centre, said it marked a "breakthrough in controlling a mechanical arm with high precision on the lunar surface".
At the weekend, the lander and rover "woke up" from a period of hibernation lasting two weeks - equivalent to one lunar night.
Both vehicles draw much of their power from solar arrays, which means they must conserve energy when darkness falls on their landing site.
Radioisotope heating units, powered by plutonium-238, keep the rover warm in the lunar night, during which temperatures can drop as low as -180C (-292F).
Quelle: BBC
.
Update: 18.01.2014
.
China's lunar probe observes stars, explores moon

Moon lander Chang'e-3 and rover "Yutu" of China's lunar probe mission have collected a large amount space observation and moon exploration data, a government authority said on Friday.

A moon-based optical telescope on the lander has been observing lights from many celestial objects at near ultraviolet wavelengths, and has detected 23 stars, said a statement from the State Administration of Science, Technology and Industry for National Defence.

After data analysis and processing, scientists have drafted an atlas of stars around the constellation Draco, the statement said.

Probe equipment on the rover Yutu (Jade Rabbit) is exploring the moon.

The probe radar has surveyed the moon's surface and collected two sets of data about the structure of lunar soil beneath the surface within 140 meters and 10 meters respectively, the statement said.

The panoramic camera and infrared spectrograph have sent back clear images of the moon's surface and data collected by a particle X-ray device has helped scientists identify 11 types of chemical elements such as magnesium, aluminum, calcium and yttrium on the moon, it added.

Data collected from observations of the plasmasphere over the Earth will provide more information about the impact of solar activities to the Earth, according to the statement.

These findings will provide information for scientists to better understand the terrain, geological structure, material composition and soil formation of the moon, the statement said.

.

The Chang'e-3 lunar probe has started its long-term scientific missions and will have its durability tested when it continues lunar surface surveys, sources with the Beijing Aerospace Control Center said on Thursday.

The center transferred operations of the probe to a smaller management team on Wednesday night, said Cui Yan, who leads the team at the center.

"We have made all the hardware and software ready for the long-term control tasks and have developed new management methods," Cui said, noting this is the first time China would operate a lunar probe for as long as one year.

Liu Junqi, one of the chief engineers on Cui's team, said that during the yearlong task the team will coordinate deep-space control stations around the nation to closely monitor the Chang'e-3 lander and the Yutu rover, and to arrange scientific missions on the lunar surface.

One of the major responsibilities for the team is to put the lander and rover into sleep mode when the lunar night falls and "awaken them" once the night ends, he said.

One night on the moon lasts about 14 Earth days, during which the temperature falls below minus 180 C and there is no sunlight to provide power for the instruments' solar panels.

"The transfer of control marks the successful completion of the probe's first stage of exploration and scientific missions," said a publicity officer at Beijing Aerospace Control Center who refused to be named.

He said under the long-term management mode, the lander and rover do not need a lot of people to take care of them, therefore Cui's team, which has less than 20 people, is able to take over from the current large control group.

"Next, the team will control the probe to perform scientific operations that can last several months. Engineers will test whether the lander and rover can function well over a long period and whether they can live up to their designed life span," the officer added. "During the yearlong period, the team's controllers and engineers will work about 15 consecutive night shifts each month, so this is really a tough job."

The lunar rover Yutu has a designed life span of three months, and the lander is expected to work for one year.

After waking up following nearly two weeks of dormancy, Yutu completed its first sampling of lunar soil using its mechanical arm on Tuesday, the Beijing center said.

"Accuracy control of the mechanical arm at a distance of 380,000 kilometers has been realized in the probe, marking China's breakthrough in controlling a mechanical arm with high precision on the lunar surface," said Wu Fenglei from the center.

Yutu will continue to survey the moon's geological structure and surface substances and look for natural resources, while the lander will explore the landing site until the end of its life span.

 Quelle: China Daily

.
Update: 22.01.2014
.
Chinas Yutu Rover rollt über den Mond im Zeitraffer-Panorama 
.
This time-lapse color panorama from China’s Chang’e-3 lander shows the Yutu rover at two different positions during its trek over the Moon’s surface at its landing site from Dec. 15-18, 2013. This view was taken from a 360-degree panorama – see below. Credit: CNSA/Chinanews/Ken Kremer/Marco Di Lorenzo
.
A new time-lapse photomosaic shows China’s Yutu rover dramatically trundling across the Moon’s stark gray terrain in the first week after she rolled all six wheels onto the desolate lunar plains.
Our complete time-lapse mosaic (see below) shows Yutu at three different positions trekking around the landing site, and gives a real sense of how it is maneuvering around – on the 1st Lunar Day.
The 360-degree panoramic mosaic was created from images captured by the color camera aboard China’s Chang’e-3 lander, the country’s first spacecraft to successfully soft land on the Moon.
The time-lapse mosaic was stitched together by the imaging team of scientists Ken Kremer and Marco Di Lorenzo using images just released on a Chinese language website.
We integrated the wide screen panorama with additional images of Yutu taken by the lander as she roved around the right side of the mothership during her 1st Lunar Day – to create the new time-lapse panorama.
To me the moonscape is rather reminiscent of the scenery from NASA’s manned Apollo lunar landing missions which took place over 4 decades ago – from 1969 to 1972.
.
360-degree time-lapse color panorama from China’s Chang’e-3 lander This 360-degree time-lapse color panorama from China’s Chang’e-3 lander shows the Yutu rover at three different positions during its trek over the Moon’s surface at its landing site from Dec. 15-22, 2013 during the 1st Lunar Day. Credit: CNSA/Chinanews/Ken Kremer/Marco Di Lorenzo – kenkremer.com
.

Here’s the original 360 degree panorama:

.

1st 360 Degree Color Panorama from China’s Chang’e-3 Lunar Lander. This 1st color panorama from Chang’e-3 lander shows the view all around the landing site after the ‘Yutu’ lunar rover left impressive tracks behind when it initially rolled all six wheels onto the pockmarked and gray lunar terrain on Dec. 15, 2013. Mosaic Credit: CNSA/Chinanews/Ken Kremer/Marco Di Lorenzo – kenkremer.com
.
The first portrait of Yutu was taken shortly after it first drove off the 1200 kg Chang’e-3 lander on Dec. 15. The last Yutu position shows her heading off to the south and departing the landing site forever.
She’s not ever coming back to see the stationary lander again, according to China’s Chang’e-3 mission team.
Yutu, which translates as ‘Jade Rabbit’, is on her own from now on.
.
This view shows the Yutu rover heading south from the Chang’e-3 landing site about a week after the Dec. 14, 2013 touchdown at Mare Imbrium. This cropped view was taken from the 360-degree panorama. The extreme ultraviolet camera is at right. Credit: CNSA/Chinanews/Ken Kremer/Marco Di Lorenzo – kenkremer.com
.
Chang’e-3 safely touched down on the Moon at Mare Imbrium near the Bay of Rainbows on Dec. 14, 2013.
Seven hours later, the piggybacked 140 kg Yutu robot drove off a pair of ramps, onto the Moon and into the history books.
Here is the initial black and white panoramic version from the Chang’e-3 navigation camera – which we assembled from screenshots taken as it was twirling about in a CCTV news video report.
.
1st panorama around Chang’e-3 landing site after China’s Yutu rover drove onto the Moon’s surface on Dec. 15, 2013. The images were taken by Chang’e-3 lander following Dec. 14 touchdown. Panoramic view was created from screen shots of a news video assembled into a mosaic. Credit: CNSA/CCTV/screenshot mosaics & processing by Marco Di Lorenzo/Ken Kremer
.
The Chang’e-3 mothership and Yutu rover are now working during their 2nd Lunar Day, having survived the harsh extremes of their 1st Lunar Night when temperatures plummeted to below minus 180 degrees Celsius, or minus 292 degrees Fahrenheit.
They have resumed full operation and are conducting research investigations. Each is equipped with four science instruments.
All the equipment is functioning well except alas for the color camera used to snap the images for the photomosaics herein.
.
Photo of Chang’e-3 moon lander emblazoned with Chinese national flag taken by the panoramic camera on the Yutu moon rover on Dec. 22, 2013. Credit: CNSA
.
China’s official Xinhua new agency reports that the instruments aboard the lander and rover have each collected a large amount of data about the Moon, Earth and celestial objects.
Scientists have created a star atlas around the constellation Draco and used the ground penetrating radar to survey the moon’s subsurface and soil structure to depths of 10 to 140 meters.
Meanwhile as China’s Yutu rover trundles across pitted moonscapes, NASA’s Opportunity rover is in the midst of Martian mountaineering at the start of Decade 2 on the Red Planet and younger sister Curiosity is speeding towards the sedimentary layers of Mount Sharp.
Stay tuned here for Ken’s continuing Chang’e-3, Orbital Sciences, SpaceX, commercial space, LADEE, Mars and more news.
.
Traverse Path of Yutu rover from Dec. 14 landing to Dec. 21. Landscape textured with Chang’e 3 imagery from space and ground. Credit: CNSA/BACC
Quelle: UniverseToday
.
Update: 25.01.2014
.

China's moon rover monitored with abnormity

BEIJING, China's moon rover "Yutu" (Jade Rabbit) has had an abnormity, and scientists are organizing an overhaul, the State Administration of Science, Technology and Industry for National Defence said on Saturday.

Quelle: Xinhua

- Update

.

China Exclusive: China's moon rover experiences abnormality


BEIJING, China's moon rover, Yutu (Jade Rabbit), has experienced a mechanical control abnormality, and scientists are organizing repairs.

The abnormality occurred due to "complicated lunar surface environment," the State Administration of Science, Technology and Industry for National Defence (SASTIND) said on Saturday, without giving further details.

The abnormality emerged before the rover entered its second dormancy at dawn on Saturday as the lunar night fell, according to SASTIND.

The lander, another part of the Chang'e-3 probe, also "fell asleep" earlier on Friday.

The pair went dormant for two weeks about one month ago when the first lunar night of the mission occurred.

One night on the Moon is about 14 days on Earth, during which the temperature falls below minus 180 Celsius. During the lunar night, there is no sunlight to provide power to Yutu's solar panel.

After the first dormancy, the lander's Moon-based optical telescope carried out observation of the sky, while its extreme ultraviolet camera observed the plasmasphere over the Earth, according to SASTIND.

An Ultra High Frequency communication test between the lander and the moon rover was also conducted.

The rover obtained scientific data through its radar, panorama camera, a particle X-ray device and infrared imaging equipment, said SASTIND.

The Chang'e-3 lunar probe soft-landed on the Moon on Dec. 14. Yutu separated from the lander hours later.

The success of the Chang'e-3 mission makes China the third country to soft-land a spacecraft on lunar soil after the United States and the former Soviet Union.

Humans have conducted a total of 130 lunar probe activities with a success rate of only about 51 percent, Wu Weiren, chief designer of China's lunar probe program, said in an earlier interview with Xinhua.

China's lunar probe missions -- Chang'e-1, 2, and 3 -- have all succeeded, according to Wu.

Lunar probe mission failure is not rare. In April 1962, the U.S. lunar probe Ranger 4 crashed into the dark side of the Moon after equipment failure prevented it from returning pictures and scientific data.

Japan launched a lunar probe in 1990, which soon moved off course. It failed to transmit any data and crashed into the Moon in 1993.

India managed to send a lunar probe into space in 2008, but an equipment in the main craft malfunctioned several months later, leading to the loss of contact with the unmanned spacecraft.

Quelle: Xinhua

.

Update: 26.01.2014

.

Netizens extend blessings to troubled lunar rover


BEIJING, Tens of thousands of Chinese netizens have sent their blessings to lunar rover Yutu (Jade Rabbit) after it experienced major trouble.

A mechanical control abnormality occurred to Yutu because of the "complicated lunar surface environment," said China's State Administration of Science, Technology and Industry for National Defence (SASTIND) on Saturday. Repair work is ongoing.

The news caused a splash on China's social networking circles.

People not only hailed the authority's openness to the accident, but also expressed concern.

By Sunday afternoon, more than 36,000 reposts had been generated under the "yueqiucheyutu" or "lunar rover yutu" account on Sina Weibo, China's Twitter.

The weibo account is believed to belong to space enthusiasts who have been following Yutu's journey to the moon. It has more than 110,000 followers.

Many netizens fear for the troubled rover's destiny.

"You have done a great job Yutu. You have endured extreme hot and cold temperatures and shown us what we have never seen. Hope you get well soon, but no matter what, it is your presence that makes the planet about 390 thousand kilometers away dazzling," wrote "Amaniandlove".

Zhang Yian, a Beijing-based writer, said Yutu has shouldered more than just the hope of China's space industry but also the dreams of the Chinese people. "This is too heavy a burden. If the rabbit can not stand again, maybe we should let it have a rest."

"Tanwie" wrote on weibo, "Space exploration, the more gorgeous a view you see, the more dangerous it can be."

The problem happened just before Yutu was about to begin its second dormancy in the lunar night. One night on the moon is about 14 days on Earth. During this time, the temperature falls below minus 180 Celsius.

The rover has obtained scientific data through its radar, panorama camera, a particle X-ray device and infrared imaging equipment, according to the SASTIND.

The rover was expected to stay on the moon for at least three months after it separated from the Chang'e-3 probe which soft-landed on the moon on Dec. 14.

Saturday also marked the 10th anniversary of rover Opportunity's landing on Mars. A weibo account called "NASAzhongwen" or "Chinese NASA," posted a message on Sina Weibo, wishing Yutu to get well soon.

The account has no official connection with the National Aeronautics and Space Administration, but it has documented space activities as well as the journey of Mars rovers Opportunity and Curiosity.

Compared with Opportunity's 10 years on Mars, Yutu's one-month stay is not long. But the occurrence of such an abnormality is normal, said Yang Yuguang, a researcher from China Aerospace Science & Industry Corp., deeming the Chang'e 3 probe mission as one of the most difficult in the country's space exploration.

Human kind has only achieved a 51 percent success rate on lunar probe missions among the 130 in total, according to China's lunar probe program chief designer Wu Weiren, in an earlier interview with Xinhua.

"There is no smooth way ahead. Whether or not we can overcome this difficult situation, it's a big lesson for our lunar exploration research," said Yang.

On Sunday afternoon, messages continued to be posted on Sina Weibo. "Come on little rabbit, you must hang on in there to see the Spring Festival fireworks," wrote "Dourentao".

Quelle: Xinhua

.

Update: 12.02.2014 

.

Farewell to Yutu
A virtual Yutu and associated lander as seen from mission control.
By now, it seems almost certain that China's Yutu Moon rover has died a premature death in the cold lunar night. The rover has been exposed to sunlight for a few days, and there has been no word of it waking up.
Yutu was carried to the Moon aboard China's Chang'e-3 Moon lander, a boxy structure reminiscent of the base of an Apollo lunar lander from the 1960s. Chang'e-3 made history by becoming China's first mission to land on the Moon, and the first object to softly land there in more than three decades.
Yutu's problems began roughly three weeks ago when a solar panel failed to fold inwards over the rover's body, just before night fell at the rover's landing site. The folding panel was designed to protect the rover's interior during the two-week lunar night, by trapping heat from a radioisotope source. Without this protection, the rover's electronics have apparently frozen.
China had originally expected Yutu to function for roughly three months. The failure of Yutu after less than a month of nominal surface operations is a disappointment.
Apart from mourning its loss, the major priority for China's space program will be conducting a post-mortem for Yutu. It is vital to know how it malfunctioned. Fortunately, there seems to be a lot of data that was obtained before night fell.
We know that the solar panel did not close. We can easily deduce how this affected the thermal protection for the rover. Much work will need to be performed to work out exactly why this mechanical failure occurred in the first place.
Moving parts are always tricky for spacecraft. Getting them to work on the Moon is even more difficult. Apart from the vicious cycles of heat and cold, there is the ever present problem of dust. We do not know if the hinges were jammed by dust, or if there was a failure of the motors or mechanisms designed to close the panel for some other reason. Lubricant could have been worn away from some part, causing friction or even a "cold welding" of metal surfaces in a vacuum. China will probably be conducting simulations to determine the most likely cause.
With Yutu's case file certain to close in the near future, it will be time to consider the fate of China's next Moon mission. China has already built a back-up lander, dubbed Chang'e-4, which it planned to launch in a few years. This is a typical strategy of China's lunar exploration program: Two identical spacecraft are built in case one fails.
China's first lunar mission, Chang'e-1, was launched to orbit the Moon in 2007. The mission was a complete success. Thus, China decided that its back-up spacecraft, Chang'e-2, would not precisely repeat its predecessor's mission. It was launched in 2010 with a more powerful rocket that helped the spacecraft to save its fuel reserves. Chang'e-2 was sent on a shorter mission to the Moon and then flown into deep space to fly past the asteroid Toutatis.
This time, China will probably need to use the back-up lander to repeat the tasks that Chang'e-3 failed to complete. There will probably be an overview of the design of some of its most critical components, to strengthen them against failure.
This analyst expects that China will want to land a second rover with this mission, but we can expect that it will be thoroughly overhauled. China will want to ensure that the solar panel will not fail again, and will probably look for other potential problems. The next rover will probably look the same as Yutu but it will be improved.
Exactly when Chang'e-4 will launch is unclear. The problems experienced by this latest mission suggest that China will want to take a fair amount of time for troubleshooting, redesign and testing. Any previous speculation on the approximate launch time is probably no longer reliable.
We will need to wait for China to advertise a new launch timetable. In turn, this could affect the fate of the two lunar landers that are expected to come after Chang'e-4. These missions, dubbed Chang'e-5 and 6, are sample-return missions. It could take longer to launch them, and their design could be revised in the wake of the Yutu investigations.
Whatever China does with its second rover, one change should be suggested. The rover needs a new name. China should remember that saying "Yutu 2" in English sounds stranger than it does in Chinese!
Quelle: Dragonspace
.
Chang’e-3 lander and Yutu rover – from Above And Below
Composite view shows China’s Chang’e-3 lander and Yutu rover from Above And Below (orbit and surface) – lander color panorama (top) and orbital view from NASA’s LRO orbiter (bottom). Chang’e-3 lander color panorama shows Yutu rover after it drove down the ramp to the moon’s surface and began driving around the landers right side to the south. Yellow lines connect craters seen in the lander panorama and the LROC image from LRO (taken at a later date after the rover had moved), red lines indicate approximate field of view of the lander panorama. Credit: CNSA/NASA/Ken Kremer/Marco Di Lorenzo/Mark Robinson
.
Landing site of Chinese lunar probe Chang’e-3 on Dec. 14, 2013.
.
Quelle: Ecns

.

Has China's Ailing Moon Rover Survived 2nd Lunar Night?

China's first moon lander, Chang'e 3, is reportedly up and running following its second encounter with the vicious lunar night cycle. But whether the lander's sidekick, the Yutu moon rover, also survived the lunar cold is not immediately clear.
The stationary Chang'e 3 lunar lander appears to have emerged from its second hibernation period following the 14-day lunar night. The reportedly now active lander went into a controlled hibernation mode on Jan. 24 Beijing Time.
Meanwhile, the mobile Yutu rover — meaning "Jade Rabbit" — may well have frozen to death. China's space agency has yet to release an official status update on the rover. The state-run China Daily newspaper reported that, as of Monday, the rover "could not be restored to full function" and that fans of the mission were mourning the development on Weibo, China's Twitter equivalent.

Quelle:spacecom

.

Yutu’s fans hope as lunar rover shows signs of awakening after malfunction 

.

China's first moon rover Yutu, or Jade Rabbit, showed signs of awakening on Wednesday following a malfunction at the beginning of the second lunar night of its mission.
"The little rabbit is getting better and shows some signs of awakening. Let's wait," the Xinhua News Agency quoted an anonymous source from the space mission as saying. 
Thousands of Chinese Net users sent best wishes to the rover as the third lunar day began via a Sina Weibo account in Yutu's name.
The status of the Chang'e probe, which is not reported to have malfunctioned, is as yet unknown, with authorities promising an update in the coming days. 
Yutu had conducted scheduled scientific research on the Moon since December 15, 2013. It awakened from the first lunar night on January 11, but a mechanical malfunction was detected on January 25 before going dormant for the second lunar night.
One lunar night lasts about 14 days on Earth, during which Yutu has to power-down to survive the -180 C surface temperature. 
After Yutu failed to power-up Monday, data about its current condition and repair progress is still being collected and analyzed. This will be published promptly when ready, the State Administration of Science, Technology and Industry for National Defense told the Global Times Wednesday. 
A Sina Weibo account in the voice of Yutu itself has attracted more than 270,000 followers, in which Net users have been leaving comments as if Yutu is a living figure from Chinese myth. 
The account has not been updated since January 25 after it said good night to Earth. More than 21,000 comments have been left as of late Wednesday calling for it to get up and encourage it to fight, with many said they shed tears reading the lines.
"Bunny you got to get up … OK I have to study now because several years later I'm getting up there to get you damn rabbit back," wrote a 19-year-old boy with the screen name w9N.
While the Chang'e-3 mission made China the third country, after the former Soviet Union and the US, to soft-land a spacecraft on lunar soil, the public have showed unusual emotion attachment to this landmark achievement via the Yutu Weibo account. 
"Thank you rabbit for telling the world that we're strong, the masters will work hard to send a buddy for you soon," wrote Weibo user Bihu.
Quelle: Global-Times

.

Update: 13.02.2014

.

Jade Rabbit back from the dead: Scientists restore communications with Moon rover - but they're still trying to fix its mechanical faults

  • Rover's process for shutting down for the lunar night has malfunctioned
  • A lunar night lasts two weeks and temperatures can drop to minus 180 °C
  • Lunar dust may have blocked one of the solar panels from folding inward, leaving equipment exposed to the dangerously low temperatures
  • Scientists won't know if probe will work until after the two-week period 
  • China has restored communications with its space programme's Jade Rabbit moon rover, but engineers are still working to fix its mechanical problems, state media said. 
    The official Xinhua News Agency cited Pei Zhaoyu, the lunar probe programme's spokesman, as saying the rover had survived the frigid cold of the lunar night that began on 25 Jan.
    The Jade Rabbit rover is designed to roam the lunar surface for three months while surveying for natural resources and sending back data.
    The problems were a rare setback for China, which in recent years has conducted space walks and placed a space station in orbit.
    Yesterday China's Jade Rabbit Moon rover was declared dead on the Moon's surface in a major setback for the country's ambitious space programme.
    But Pei said the rover had 'come back to life' despite space experts' earlier concerns that it might not survive the extremely low temperatures of the lunar night, when the temperature drops to -180ºC (-292°F).
    'The rover stands a chance of being saved now that it is still alive,' Pei was quoted as saying. He said it was still unclear what caused the problem. 
    The mission is proving a popular success for China's military-backed space programme. 
    Updates about the rover's progress have been posted on an unofficial Chinese microblog account written with Jade Rabbit's 'voice', attracting tens of thousands of comments by Chinese Internet users.
    The Jade Rabbit, or Yutu in Chinese, was deployed on the moon on December 15 and was a huge source of pride in China, which is only the third country to complete a lunar rover mission after the United States and the former Soviet Union.
    The silver rover experienced a 'mechanical control abnormality' late January due to 'the complicated lunar surface environment', according to the official Xinhua news agency, and has been unable to function since then.
    Condolences poured in on Weibo, China's Twitter-like service, where Internet users mourned the demise of the rover, according to China News Service's report titled 'Loss of lunar rover'.
    The Jade Rabbit rover had previously sent back its first pictures from the moon and officials lauded the first lunar soft landing in nearly four decades as a step forward for 'mankind as a whole'.
    'Exploration of outer space is an unremitting pursuit of mankind,' China's space agency, the State Administration of Science, Technology and Industry for National Defence (SASTIND) said after the rover was deployed on the moon.
    The mission reflects 'the new glory of China to scale the peaks in world science and technology areas,' it said, adding it was committed to exploring and using space 'for peaceful purposes'.
    The lunar mission, which comes a decade after China first sent an astronaut into space, is seen as a symbol of the country's rising global stature and technological advancement, as well as the Communist Party's success in reversing the fortunes of the once-impoverished nation. 
    Beijing plans to establish a permanent space station by 2020 and eventually send a human to the moon.
    The potential to extract the moon's resources has been touted as a key reason behind Beijing's space programme, as the moon believed to hold uranium, titanium, and other mineral resources, as well as offering the possibility of solar power generation.
    The six-wheeled Yutu vehicle began operating last month after making the first soft landing on the moon by a space probe in 37 years.
    It is designed to roam the lunar surface for three months while surveying for natural resources and sending back data, along with its stationary lander, Chang'e 3.
    Over 150,000 people follow the rover's progress on its microblog, which posted on Saturday that repairs were underway and that all hope was not lost.
    ‘Sorry to make you all sad. The engineers and I haven't given up yet,’ the post said.
    News of the rover's troubles were splashed across Chinese newspapers on Monday and even featured at the Foreign Ministry's daily briefing.
    The problems appeared to be related to the solar-powered probe's process for shutting down for the lunar night, which lasts more than two weeks.
    The probe had survived its first shutdown, during which it was unable to generate energy from its solar panels and relies on a radioactive power source to keep its delicate sensors and other equipment intact.
    The rover was traversing a relatively flat part of the moon known as Sinus Iridum, or the Bay of Rainbows, at a speed of 200 yards per hour.
    The landing vehicle, which has already shut down for the lunar night, is designed to conduct scientific examinations for one year.
    Online speculation focused on the possibility of lunar dust having blocked one of the solar panels from folding inward, leaving equipment exposed to the dangerously low temperatures.
    .
    Quelle: Daily Mail
    It will not be known if the probe is able to function again until after the two-week break.

.
Update:
.
China's lunar rover wakes after mechanical issues
.
BEIJING, China's moon rover Yutu has "woken" after its troubled dormancy but experts are still trying to find out the cause of its technical problems, a spokesman with the country's lunar probe program said on Thursday.
"Yutu has come back to life," said Pei Zhaoyu, after a period in which the rover's inactivity had threatened the completion of its mission.
Pei said Yutu, named after the pet of a lunar goddess in ancient Chinese mythology, has now returned to a state where it can receive signals as normal once again. But experts are still working to verify the cause of its mechanical control issues.
Yutu was designed to roam the lunar surface to survey the moon's geological structure and surface substances and look for natural resources. It was expected to work on the moon for at least three months.
But problems emerged before the rover entered its second dormancy on the moon on Jan. 25 as the lunar night fell. Experts feared that it might never be able to function again.
"Yutu went to sleep under an abnormal status," Pei said, adding that experts had been concerned that it might not be able to survive the extremely low temperatures during the lunar night.
One night on the moon is about 14 days on Earth, during which the temperature falls below minus 180 degrees Celsius. During the lunar night, there is no sunlight to provide power to Yutu's solar panel. In this period, the rover is expected to stay in a power-off mode and communication with Earth is also cut off.
Yutu entered the first period of dormancy on Dec. 26 as the mission's first lunar night arrived, and "woke up" on Jan. 11. It was originally scheduled to wake up from the second dormant period on Feb. 10.
"Now that it is still alive, the rover stands a chance of being saved," Pei said.
The news caused a splash in China's social networking circles.
On Sina Weibo, China's Twitter, the "Yutu Lunar Rover" account, which has followed the developments of the mission from a first-person perspective, posted its first update since the mechanical problems.
"Hi, anybody there?" it asked in a post, which prompted some 60,000 reposts and 40,000 comments within two hours.
"We are all here," one Weibo user replied.
"Hold on there, the whole country's got your back," another wrote.
Some joked about the rover being a "foodie" waking up for rice dumplings, a must-have delicacy for China's Lantern Festival that falls on Friday.
"Which would you prefer? Chocolates or rice dumplings?" asked one user with the screen name "shengkongtangjiang." This year's Lantern Festival falls on the same day as Valentine's Day.
Fans overseas also posted messages on Twitter.
"Makes me want to dance a jig," one user wrote minutes after the official @XHNews account posted the news that Yutu had woken up.
"PRC engineers & scientists shld [sic] be proud of their excellent work, & congratulations to them from all of humankind," another user named "jeffsonstein" said.
Lunar probe mission failures are not rare. In April 1962, U.S. lunar probe Ranger 4 crashed into the dark side of the moon after equipment failure prevented it from returning pictures and scientific data.
Yutu touched down on the moon's surface on Dec. 15, several hours after China's lunar probe Chang'e-3 soft-landed on the moon on Dec. 14.
Chang'e-3 is part of the second phase of China's lunar program, which includes orbiting, landing and returning to Earth. It follows the success of the Chang'e-1 and Chang'e-2 missions in 2007 and 2010.
China is the third country in the world to successfully soft-land on the moon after the United States and the Soviet Union.
Quelle: Xinhua

.

Update: 22.02.2014

.

No Call for Yutu

.

Well over a week since daylight returned to its landing site, China's Yutu Moon rover seems to be damaged beyond any practical use. That's the only reliable conclusion this analyst can reach after days of reading the available evidence, considering the options, and waiting for any sort of good news.

It is true that China reported that Yutu had made some sort of transmission a few days after sunrise. This shows that the rover was not completely dead at the time. However, this form of erratic transmissions, followed by silence, is typical of the way spacecraft die.

We have seen it so many times before. Ironically, the sunlight that was expected to heal the rover back to health may have damaged it even further as the lunar day advanced. Parts that could have been damaged by the cold lunar night could have been fractured or warped as they heated.

Is Yutu just severely damaged or is it totally dead? Right now, that's inconclusive. This writer suggested in an earlier article that it would take China some time to diagnose Yutu's faults and work out a strategy to use the rover.

This would take some time, and that would justify China's silence. Well, there has now been more than enough time to make a diagnosis and draw up some plans. China should say something new about Yutu. The world wants to know.

The overall forecast for Yutu grows bleaker with every day of inactivity and silence from Chinese officials. The world understands this, and has generally embraced Yutu and the Chang'e-3 mission that landed it with the support it deserves.

Millions of people around the world feel that they are stakeholders in this mission, just as China wanted. We need closure on the fate of our little robotic friend.

Quelle: SD

.

Update: 23.02.2014

.

China Focus: Uneasy rest begins for China's troubled Yutu rover

.

This undated photo taken by the camera on the Yutu moon rover shows the Chang'e-3 moon lander and the moon surface. The Chang'e-3 lander entered its third dormancy on early Feb. 23, 2014. China's lunar rover Yutu also entered the dormancy on Feb. 22, with the mechanical control issues that might cripple the vehicle still unresolved. According to the State Administration of Science, Technology and Industry for National Defence (SASTIND), Yutu only carried out fixed point observations during its third lunar day, equivalent to about two weeks on Earth. Yutu's radar, panorama camera and infrared imaging equipment are functioning normally, the control issues that have troubled the rover since January persist. (Xinhua/SASTIND)

.

China's lunar rover Yutu entered its third planned dormancy on Saturday, with the mechanical control issues that might cripple the vehicle still unresolved.

According to the State Administration of Science, Technology and Industry for National Defence (SASTIND) on Sunday, Yutu only carried out fixed point observations during its third lunar day, equivalent to about two weeks on Earth.

Yutu's radar, panorama camera and infrared imaging equipment are functioning normally, but the control issues that have troubled the rover since January persist.

The rover went to sleep mode on Saturday afternoon.

During the lunar night, there is no sunlight to power Yutu's solar panels. In this period, the rover is expected to stay in a power-off mode and communication with Earth is cut.

Yutu, named after the pet rabbit of the lunar goddess Chang'e in Chinese mythology, touched down on the moon's surface on Dec. 15, some hours after lunar probe Chang'e-3 landed.

The rover was designed to roam the lunar surface for at least three months to survey the moon's geological structure and surface substances and look for natural resources.

But problems emerged before the rover entered its second dormancy on the moon on Jan. 25 as the lunar night fell. According to SASTIND, the mechanic control abnormality occurred due to the "complicated lunar surface"

Experts had feared that it might never function again, but Yutu "woke up" on Feb. 12, two days behind schedule, and caused a stir in China's social networking circles.

A the awakening was announced by an unverified user named "Jade Rabbit Lunar Rover", which posts first-person accounts in the "voice" of the probe, and has gone viral on Weibo.com.

"Hi, anybody there?" it asked, prompting over 60,000 reposts and 40,000 comments within two hours.

Its latest post on Sunday, which featured a picture of the Chang'e-3 probe taken by Yutu during its third lunar day and the caption of "zzZ", implicating the lunar rover had gone asleep, were also reposted by thousands within minutes.

"Remember to wake up on time, you lazy bones," one wrote in reply.

Meanwhile, the Chang'e-3 lunar probe, which carried Yutu to the moon's surface, also entered dormancy in the wee hours of Sunday morning, after carrying out observations of celestial bodies and the Earth's plasmasphere using its optical telescope and extreme ultraviolet camera.

China is the third country to soft-land on the moon after the United States and the Soviet Union.

Chang'e-3 is part of the second phase of China's lunar program, which includes orbiting, landing and returning to Earth. The country has also sent probes to orbit the moon in 2007 and 2010, the first of which crashed onto the lunar surface at the end of its mission.

The second probe was sent to verify key technologies for Chang'e-3 and reconnoitered the landing area, before being sent into deep space.

According to the SASTIND, the Chang'e-2 has become China's first man-made asteroid, and is currently 70 million kilometers from the Earth.

Quelle: Xinhua

 .

Update: 1.03.3014

.


China Exclusive: Control circuit malfunction troubles China's Yutu


BEIJING, China's Yutu (Jade Rabbit) moon rover suffered a control circuit malfunction in its driving unit, which troubled its dormancy in extremely low temperature, a scientist said on Saturday.

The control circuit problem prevented Yutu from entering the second dormancy as planned, Ye Peijian, chief scientist of the Chang'e-3 program, told Xinhua in an exclusive interview.

"Normal dormancy needs Yutu to fold its mast and solar panels," said Ye. "The driving unit malfunction prevented Yutu to do those actions."

Ye, a member of the National Committee of the Chinese People's Political Consultative Conference, the country's top political advisory body, added, "This means Yutu had to go through the lunar night in extremely low temperatures."

Yutu, named after the pet rabbit of the lunar goddess Chang'e in Chinese mythology, touched down on the moon's surface on Dec. 15, a few hours after lunar probe Chang'e-3 landed.

The rover was designed to roam the lunar surface for at least three months to survey the moon's geological structure and surface substances and look for natural resources.

But problems emerged before the rover entered its second dormancy on the moon on Jan. 25 as the lunar night fell. Experts had feared that it might never function again, but it "woke up" on Feb. 12, two days behind schedule.

At present every piece of equipment of Yutu, which is undergoing another dormancy, is getting back to normal, the state of the rover is not encouraging, Ye said.

"We all wish it would be able to wake up again," said Ye ahead of the annual session of the top advisory body, which is scheduled to open on Monday.

Quelle: Xinhua

.

Update: 8.03.2014

.

NASA Lunar Orbiter snaps Spectacular Images of Yutu Moon Rover driving around Chang’e-3 Lander

Yutu rover drives around Chang’e-3 lander – from Above And Below
Composite view shows China’s Yutu rover and tracks driving in clockwise direction around Chang’e-3 lander from Above And Below (orbit and surface). The Chang’e-3 timelapse lander color panorama (bottom) and orbital view (top) from NASA’s LRO orbiter shows Yutu rover after it drove down the ramp to the moon’s surface and began driving around the landers right side, passing by craters and heading south on Lunar Day 1. It then moved northwest during Lunar Day 2. Arrows show Yutu’s positions over time.
Credit: CNSA/NASA/Ken Kremer/Marco Di Lorenzo/Mark Robinson

.

The powerful telescopic camera aboard NASA’s Lunar Reconnaissance Orbiter (LRO) has captured spectacular new images detailing the traverse of China’s Yutu moon rover around the landing site during its first two months exploring the Moon’s pockmarked grey terrain.

The newly released high resolution LRO images even show Yutu’s tracks cutting into the lunar surface as the world famous Chinese robot drove in a clockwise direction around the Chang’e-3 lander that delivered it to the ground in mid-December 2013.

You can precisely follow Yutu’s movements over time – from ‘above and below’ – in our new composite view (shown above) combining the latest LRO image with our timelapse mosaic showing the rover’s history making path from the touchdown point last December to today’s location.

Yutu is China’s first ever Moon rover and successfully accomplished a soft landing on the Moon on Dec. 14, 2013, piggybacked atop the Chang’e-3 mothership lander.

Barely seven hours after touchdown, the six wheeled moon buggy drove down a pair of ramps onto the desolate gray plains of the lunar surface at Mare Imbrium (Sea of Rains) covered by volcanic material.

.

LROC February 2014 image of Chang’e 3 site. Blue arrow indicates Chang’e 3 lander; yellow arrow points to Yutu (rover); and white arrow marks the December location of Yutu. Yutu’s tracks can be followed clockwise around the lander to its current location. Image width 200 meters (about 656 feet). Credit: NASA/Goddard/Arizona State University

.

Altogether three images of the rover and lander have been taken to date by the Lunar Reconnaissance Orbiter Camera (LROC) aboard LRO – specifically the hi res narrow angle camera (NAC).

The LROC NAC images were captured on Dec. 25, 2013, Jan. 21, 2014 and Feb. 17, 2014 as LRO soared overhead.

The four image LRO composite below includes a pre-landing image taken on June 30, 2013.

.

Four LROC NAC views of the Chang’e 3 landing site. A) before landing, June 30, 2013 B) after landing, Dec. 25, 2013 C) Jan. 21, 2014 D) Feb. 17, 2014 Width of each image is 200 meters (about 656 feet). Follow Yutu’s path clockwise around the lander in “D.” Credit: NASA/Goddard/Arizona State University

.

Since the solar incidence angles were different, the local topography and reflectance changes between images showing different levels of details.

“In the case of the Chang’e 3 site, with the sun higher in the sky one can now see the rover Yutu’s tracks (in the February image),” wrote Mark Robinson, Principal Investigator for the LROC camera in an LRO update.

The solar powered rover and lander can only operate during periods of lunar daylight, which last 14 days each.

During each lunar night, they both must power down and enter hibernate mode since there is no sunlight available to generate power and no communications are possible with Earth.

Here is a gif animation from the NASA LRO team combining all four LROC images.

.

Four views of the Chang’e 3 landing site from before the landing until Feb. 2014. Credit: NASA/GSFC/Arizona State University

.

During Lunar Day 1, Yutu drove down the landers ramps and moved around the right side in a clockwise direction.

By the end of the first lunar day, Yutu had driven to a position about 30 meters (100 feet) south of the Chang’e-3 lander, based on the imagery.

After awakening for Lunar Day 2, Yutu then moved northwest and parked about 17 meters (56 feet) southwest of the lander, according to Robinson.

By comparing the Janaury and February images “it is apparent that Yutu did not move appreciably from the January location,” said Robinson.

At this moment Yutu and the companion Chang’e-3 lander are sleeping through their 3rd Lunar Night.

They entered hibernation mode on Feb. 22 and Feb. 23, 2014 respectively.

Hopefully both probes will awaken from their slumber sometime in the next week when the Moon again basks in daylight glow to begin a 4th day of lunar surface science operations.

“We all wish it would be able to wake up again,” said Ye Peijian, chief scientist of the Chang’e-3 program, according to CCTV, Chin

5533 Views
Raumfahrt+Astronomie-Blog von CENAP 0